DC Motor Drive Circuit Design

DC motor drive circuit

DC motor drive circuits can be packaged in small modules like the board pictured here.

Motor drives, as the name suggests, are used to drive motors and control their speed, as well as direction of rotation. Motor driver ICs are basic current amplifiers that are responsible for delivering the required power to a motor. However, the term “motor drive” could also collectively refer to an overall system that is designed to control the motion of various motors. These systems could also be built from discrete components, particularly when higher powers are needed.

In this article, we’ll look at motor drive circuits at the system level, where the driver components are integrated into the same system with the motor and control circuitry. The driver section itself is normally a bridge circuit with a specific driving configuration; we’ll look at these driving configurations in this article.

DC Motor Drive Circuits at a High Level

Motor drive circuits and systems integrate multiple components into a single package or assembly. At the highest level, motor drives include the set of functional blocks shown in the diagram below.

DC motor drive circuit designThe microcontroller portion triggers when the driver circuit begins operating, and it may process data received from the driver circuit if there is any kind of feedback on position or speed (such as with a motor resolver). The driver circuit includes all of the circuitry needed to excite the driver circuit, although excitation can be provided by the microcontroller if the drive circuit can be triggered at logic levels. This can be the case in MOSFET motor driver circuits with moderate power output.

H-Bridge Motor Drive Topology

The most common DC motor drive circuit topology is an H-bridge circuit. This circuit is shown below, and its H-shaped topology gives it its name. DC motors can be operated in both clockwise and counter-clockwise directions using an H-bridge by controlling the directions of the driving currents in each of the MOSFETs in the circuit.

DC motor drive circuit design

MOSFETs are the most common components used to implement an H-bridge design. Turning Q1 and Q4 ON causes the motor to run in one direction while closing Q2 and Q3 causes the motor to move in the opposite direction. The same driver circuit can be operated with pulse width modulation (PWM), which allows the speed to be dynamically controlled during operation.

Alternative Motor Drives With Controllers

H-Bridge drive circuitry consists of the electronic components that connect the PWM or similar digital control inputs to the MOSFET gates. It serves two primary functions:

  • Drive the gates by converting the input voltages to the proper levels.
  • Feed a sufficient amount of current to rapidly charge and discharge the gates.

In addition, several driving circuits have other features such as:

  • Drive modes dictate how the input command is converted into signals for driving gates.
  • Incorporate extra safety features, such as over-current protection
  • Regulate the length of time that the FETs are on and off.

The common driver controller circuits are summarized in the table and image below. It is worth mentioning at this point that all MOSFETs used on the low side are N-channel, but both P-channel and N-channel devices can be used on the high side.


Low-side driver

These are built specifically to drive either Q2 or Q4 in the H-bridge described above

High-side driver

These are built specifically to drive either Q1 or Q3 in the H-bridge described above

Half-bridge driver

Consists of a single low-side and high-side driver that operate in tandem to control Q1 and Q2 (or Q3 and Q4).

Full-bridge driver

Consists of two high-side and low-side drivers that can drive all four MOSFETs collectively

DC motor drive circuit design

Challenges in H-Bridge Motor Drivers Design

While the process of designing motor drivers based on an H-bridge may seem easy at first glance, it is not without its difficulties. These may occur during either the circuit design phase or the firmware development phase. In an H-bridge circuit, the FETs turn ON and OFF in a diagonal pattern, but this switching cannot happen simultaneously among all FETs.

Dead Time: There will always be a point in time when all transistors will be open. If the top and lower switches are both turned on, there will be a momentary loss of voltage and power, or possibly a short. Dead time can be implemented to prevent this from happening. This is the brief time during which all FETs in the H-bridge are ON. Dead time allows the programmer to delay the opening of the topmost switch until the bottommost one has been closed.

PWM Frequency: Another crucial element that has to be set correctly when designing a motor driver is the PWM frequency. More power will be lost at lower frequencies and vice versa. If the PWM frequency is too high, however, the microcontroller may struggle to provide the necessary PWM signal at the required bias. Furthermore, the gate driver and transistor switches may fail due to incompatibility with a very high frequency. The proper PWM frequency must be set up in the firmware in order to guarantee the motor controller's proper functioning.

EMI: Finally, extreme EMI is also an issue that may arise with certain types of motors, such as brushed DC motors. This is caused by frequent switching of the commutator, and this can inject noise into nearby components. In extreme cases, conducted currents can damage nearby components. Filters and ferrites are often used to shield cables that could pick up this EMI, particularly at lower frequencies where most of the power will be concentrated.

MOSFET Selection for H-Bridge Motor Drive Circuits

MOSFETs should have some important specifications if they are to be used in motor drive circuits:

  • High voltage and current handling capability
  • Low ON-state resistance
  • Lowest possible lead inductance

To increase the current handling capabilities of MOSFETs used in motor drive circuits, these components will often be placed in series.

The lead inductance and PCB layout are both important for determining the total inductance on the drive path. During startup, excessive inductance can lead to an underdamped oscillation in the drive circuit that can damage or destroy the MOSFETs. As a result, some transient voltage protection is needed on the MOSFETs. This can be as simple as a TVS diode and a small resistor in series with the gate, and a fast recovery diode should be placed across the motor.

When you’re ready to design and simulate your DC motor drive circuits, make sure you use the industry’s best circuit design and simulation tools in PSpice from Cadence. PSpice users can access a powerful SPICE simulator as well as specialty design capabilities like model creation, graphing and analysis tools, and much more.

Subscribe to our newsletter for the latest updates. If you’re looking to learn more about how Cadence has the solution for you, talk to our team of experts.

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
Are Pull-up Resistors Needed on Push-Pull Buses?
Are Pull-up Resistors Needed on Push-Pull Buses?

The classic push-pull bus is SPI, but do you need pull-up resistors for this protocol?

Next Article
Clocking ADCs in Mixed-Signal Systems
Clocking ADCs in Mixed-Signal Systems

ADC clocking can involve reference oscillators, multiple ADCs, source-synchronous clocks, or embedded clock...

OrCAD Free Trial

Try OrCAD Today