The Advantages of Wave Soldering

Key Takeaways

  • Wave soldering is an assembly process by which a molten wave of solder passes on the underside of the board, forming a solder joint between pin and pad.

  • Placement can inhibit the effectiveness of the wave soldering process in tight designs.

  • Wave soldering is a much faster and more economic method of mass soldering than solder reflow.

 Surface of a molten metal pool

A molten solder pool provides the soldering material for through-hole components

Following layout design and fabrication, the final step before verifying the completeness of a board is the assembly. Components need to be placed and securely bonded to the board to meet their intended functionality. Soldering, however, has progressed far beyond the handheld iron of hobbyists and simple boards. When dealing with hundreds (or even thousands) of components in a design, including those that can be barely visible without some magnification, automated services need to be employed. This is especially true when producing lots of appreciable volumes–simply, time is money. Wave soldering is the older of the two mass soldering processes, but this is not a case of technological obsolescence; there are advantages of wave soldering that persist to this day.

What Is Wave Soldering?

Wave soldering is a technique that is essential for bulk PCB production containing through-hole components. In this process, a board is passed through a wave solder machine that controls the height of the standing wave as well as the amount of time each board spends in contact with it. As the board is propelled through the machine, the liquid solder can make contact between the pin and the surrounding pad, quickly making a conductive solder joint. The entire process of soldering involves some additional steps beyond submitting the boards to the wave:

  1. Flux application - To ensure the cleanliness of the soldering site, flux is used to remove oxides, prevent the formation of new oxide layers, and assist the wetting of the solder to the soldering surface, which assists with joint formation and structure. Excess flux residue may or may not need to be cleaned.

  2. Preheating - The boards are brought up to temperature to engage the applied flux and prevent thermal shock due to the high temperatures of the molten solder.

  3. Wave solder - Boards pass through the molten solder wave with careful temperature controls to reach the eutectic point of the soldering material. This keeps the thermal exposure of the boards in the wave soldering process to an absolute minimum.

  4. Cooling - Converse to the preheating phase, the board is slowly returned to ambient temperature in a heated environment. The slower quenching rate is to prevent warpage to the board and allow time for the solder to set. However, boards should not be exposed to elevated temperatures any longer than necessary to prevent damage to the board and heat-sensitive components.

While lead-tin solder was the gold standard in soldering for years, RoHS compliance has eliminated it in consumer electronics. While a health issue, leaded solders have the excellent ability to prevent the formation of whiskers (extrusions of metal from the surface thought to arise to relieve intermetallic strain), which can lead to shorting of electronics and a reduction in the board’s lifetime reliability. In its place, alloy compositions such as SAC (tin, silver, copper) have risen to prominence as excellent lead-free solder that is not as susceptible to whiskering as some other alloys.

How Placement Can Affect the Effectiveness of Wave Soldering

Placement and layout will influence the effectiveness of the wave solder process. Imagine the wave passing over components as the board travels through the machine. When the wave washes over a pin and solderable surface, it momentarily leaves an absence of solder behind this section of the wave. This design consideration is known as the wave soldering shadow–essentially, the amount a component blocks the flow of solder to components behind it parallel to the direction of the wave solder. Wave shadow soldering can lead to incomplete solder joint formation and other manufacturing errors. 

There are two major issues to avoid to prevent wave solder shadowing: component spacing and rotation. Spacing may perhaps be fairly obvious - the more distance between components parallel to the direction the board is traveling through the wave soldering machine, the more time the wave has to “recover” and fully reform. Mismatched rotations can also increase the effect of solder wave shadowing. Two of the same component package, with one rotated 90° relative to another, can create a long shadow as well, depending on the orientation of the components relative to the passage through the wave solder machine. 

Through-hole components on both sides of the board will need to be soldered separately and sequentially. This raises some issues, as the board and one set of components will be exposed to the high-temperature cycle (preheating, wave solder environment, and cooling) twice, raising the chance for manufacturing errors. The best design practice, if available, is to move components to a single side of the board, though this may be far easier said than done. Failing the single-sided PCB approach, the selection of the side to undergo the temperature environment of the wave solder machine twice should be the side that has the fewest heat-sensitive components (ideally zero) or those with a higher temperature tolerance.

Isometric PCB view

The density and orientation of placement will affect how quickly the solder wave can reform

Solder Reflow and the Advantages of Wave Soldering

To understand the advantages of wave soldering, it is necessary to examine the alternate soldering technology in wide adoption: reflow soldering. Reflow soldering functions by heating the air in an oven to melt the solder paste pre-applied to the pads/pins before beginning the rest of the process. It’s a more targeted method of soldering than wave soldering, which simply applies solder over the bottom of the board as it passes over the molten wave. Overall, the reflow process exhibits a reduced thermal shock compared to wave soldering.

There are a few key advantages to wave soldering over reflow:

  • Mass production - Reflow is unable to compare to the speed of wave soldering for anything but the smallest production lots.
  • Cost scaling - As an outgrowth of its comparative speed advantage, wave soldering is far more affordable on a per-board basis than reflow.
  • Through-hole components - Wave soldering is the only way to solder through-hole components. While many components can be replaced with an SMD package, many power components still exist in a through-hole configuration, which endears wave soldering to a large market of boards.

For mass productions, it’s no contest - wave soldering is the faster and cheaper process

For all your ECAD needs, Cadence offers a robust package of PCB design and analysis software tools to provide cutting-edge solutions to your designs. Component placement and layout are simple with the Allegro PCB Editor–it’s easy to design around wave solder shadowing and gain the advantages of wave soldering in your high volume DFM board.

Leading electronics providers rely on Cadence products to optimize power, space, and energy needs for a wide variety of market applications. If you’re looking to learn more about our innovative solutions, talk to our team of experts or subscribe to our YouTube channel.

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
Allegro Shortcut Keys: A Gift for Efficient PCB Layout
Allegro Shortcut Keys: A Gift for Efficient PCB Layout

Learning how to work with Allegro shortcut keys will reduce the chance of errors and simplify working with ...

Next Article
Driving New Developments With Electronic Design Automation Using Machine Learning
Driving New Developments With Electronic Design Automation Using Machine Learning

Electronic design automation via machine learning is set to upend current development models with highly pr...

OrCAD Free Trial

Try OrCAD Today