Best RF Simulation Software

September 21, 2023 TEAM EMA

Employing the best RF simulation software during design can minimize the need for bench testing your product during development and eliminate the need once deployed

Testing is an essential part of building electronic products. In fact, testing is the proving ground where the ability of the design to achieve its operational and performance objectives is validated, or rejected. Typically, this electrical parametric testing is performed after the board spin. And, it is not uncommon to rely on contract manufacturers (CMs) to perform at least some requested in-circuit testing after assembly.

Although, this experimental verification is required, its extent is a controllable variable. Having to use laboratory testing to determine the root cause of poor signal quality or excessive EMI issues can be timely and costly. This waste of valuable resources can be avoided by performing sufficient testing with the best RF simulation software during design. 

Essential RF Simulation Software Attributes

Testing or experimentation is the fulcrum of the scientific method and the basis of functional and operational validation for electronic products. Testing can be expensive; however, and repetitious failures are not economically viable for most devices and systems. Therefore, the technological advances of the past few decades would not be possible without software simulation.

Building electronics components, devices and circuit boards without simulating in software is folly and failing to use product design software will likely lead to excessive development time–for redesigns and testing–and excessive costs–for board respins and additional engineering hours. This is especially true for RF PCBA designs where maximizing signal integrity (SI) by minimizing electromagnetic interference (EMI) or noise is a premium objective. EDA support tool capabilities do vary; however, and care must be taken to ensure that essential attributes are included.  

The Best RF Simulation Software Program Attributes




Full RF Spectrum SI Analysis

The ability to simulate and analyze signals that exist adjacent to the high-frequency RF spectrum (0+ Hz to approximately 3 GHz).

In-Design Analysis Capability

The dynamic simulation of and evaluation of component and board parameters throughout the design process.

3D Electromagnetic Analysis

Comprehensive view and analysis of electromagnetic radiation on and near the PCB.

Expansive Modeling

Accurately modeling the elements of your RF design is crucial to obtain a realistic simulation.

Comprehensive System Analysis

For a complete analysis of your RF design, both the full system and detailed building blocks must be simulated.

Software Integration and Scalability

Depending on your RF design needs, integration to other tools such as PCB design software and thermal analysis may be required.

The attributes listed above are meant to enhance or extend the effectiveness of standard 2D SI time and frequency domain modeling and simulation. These capabilities not only serve to verify that your design will achieve its performance goals, but also improve RF design development. Effective utilization of these advancements can help you optimize your process from schematic capture to manufacturing

Using RF Simulation to Optimize Development

The electronics industry is a fast-paced and dynamic environment. Competing successfully in this environment, necessitates that you seek to optimize the PCBA development process. This includes prioritizing design for manufacturing and assembly and striving for right-first-time (RFT) board builds. Ensuring your RF simulation software includes advanced capabilities is essential to realizing these objectives.

Why the Best RF Simulation Attributes Are Essential

  • Full RF Spectrum Analysis
    Many RF simulation tools target the typical high frequency RF range of up to a few gigahertz. The best tools provide you with the flexibility to design and analyze a range of signals. This includes DC signals to greater than 40 GHz, within which many electronic components and devices operate.

  • Expansive Modeling
    RF simulation requires accurate modeling of RF elements. Your RF simulation software should contain expansive models, both vendor specific and generic, to obtain a realistic representation of your RF design.

  • In-Design Analysis Capability
    It is atypical to perform post-design RF simulation, followed by redesign that may include rerouting traces, changing element placements or even choosing alternative components. This paradigm can be redundant and tedious. In-design analysis allows you to model and simulate prior to final design, which allow you to identify and make needed changes quicker and save valuable development time.

  • 3D Electromagnetic Analysis
    To be adequately appreciated and compensated for, EM effects must be viewable from all perspectives. Therefore, 3D modeling and analysis is essential to accurately determine and avoid excessive EMI/EMC.

  • Comprehensive System Analysis
    RF simulation should be performed on individual components as well as the complete system. The best RF simulation software solution seamlessly integrates the detailed analysis performed at the building block level into a full system analysis.

  • Software Integration and Scalability
    The variety of products which contain RF elements are vast, ranging from Bluetooth applications to military-grade devices. The best RF simulation software must integrate with additional capabilities to support your RF design needs. This can be through integration with power and thermal analysis or seamless integration with your PCB software design tools. 

The best RF simulation software for your project should include pertinent attributes from the above list to aid you in optimizing your development process. Additionally, your RF simulation solution should be highly scalable: allowing for more complex designs and incorporating new standards to meet your project needs as they change. For a software tool that unifies the best RF simulation attributes you should look to an industry leader in providing targeted and/or customized PCBA design solutions.  

EMA Design Automation is a leading provider of the resources that engineers rely on to accelerate innovation. We provide solutions that include PCB design and analysis packages, custom integration software, and engineering expertise, which enable you to create more efficiently. For more information on choosing the best RF simulation software for your project and how we can help you or your team innovate faster, contact us.

Previous Article
Best Software For Circuit Design and Simulation
Best Software For Circuit Design and Simulation

Choosing the best software for circuit design and simulation can be tricky. However, a set of simple guidel...

Next Article
USB Compliance Testing: What to Know
USB Compliance Testing: What to Know

Knowing the what, why, and how of USB compliance testing optimization is the key to achieving a first-time ...