Selecting Ferrite Chokes and Clamps to Minimize RFI and Resistance

February 19, 2020 Cadence PCB Solutions

Collection of ferrite clamps and chokes


When we think of ferrites, discovery and technological progress are probably the last words that come to mind. Yet, the discovery of hard ferrites or magnet material gave ancient navigators the “lodestones” that they needed to locate magnetic north. The properties associated with hard ferrites triggered the curiosity that led to the early research into electromagnetism by Oersted, Faraday, Maxwell, and Hertz. During the 1930s and 1940s, more research led to the commercial production of soft ferrite passive components that enabled progress with inductors and antennas.

What’s Right About Ferrites?

Today, power applications and our continual quest to suppress electromagnetic interference depend on the use of highly permeable soft ferrites that consist of ceramics blended from a wide range of metal oxides that form a magnetic core. The operating characteristics of ferrites depend on kinds and ratios of the metal oxides. Most ferrites consist of either a manganese-zinc blend (Mn-Zn) or a nickel-zinc (Ni-Zn) mix. Because Mn-Zn ferrites have high permeability and a low specific resistance, the ferrites remain limited to frequencies of 1MHz or less. Ni-Zn ferrites have low permeability and a high specific resistance and work well for noise suppression.

With soft ferrites, an increase in the magnetic field results in a flux density flow and magnetization occurs. If a magnetic field applies in the opposite direction, the ferrite goes back to its original condition. If a soft ferrite has a strong magnetic property, a small change in the magnetic field causes a large change in flux density.

One of the key properties for ferrites used for noise suppression is permeability. Ferrite materials that have higher permeability allow magnetic flux to pass more easily than if the flux traveled through the air. Permeability in ferrites increases as temperature increases. However, after the permeability reaches a maximum level at certain temperatures, ferrite loses permeability. While permeability changes with temperature, it remains constant up to a given frequency. In most instances, ferrite materials that have high permeability work best for high frequency circuits.

Collection of ferrites with one in the palm of a hand

Working with ferrites requires an understanding of the types of circuits they work well on. 


Because the impedance of a ferrite changes as the load current and voltage drop change, ferrite clamps and chokes function as non-linear components. The impedance of the devices becomes highly resistive for a thin band of frequencies. High frequencies cause the impedance to decrease as the ferrite becomes more capacitive than resistive. Increasing the frequencies beyond a particular threshold causes the capacitive impedance to decrease and the impedance becomes resistive.

We can use soft ferrite chokes and clamps to reduce radio frequency interference (RFI) in an electrical conductor. For that reason, ferrite chokes can attenuate interference for switched mode power supplies. Ferrite chokes--or beads--attenuate high-frequency EMI in a circuit by working as a low-pass filter. Only low frequency signals pass through a circuit. Unlike a traditional low-pass filter that works for a wide band of frequencies, ferrite chokes and clamps only attenuate frequencies that occur within the ferrite’s resistive band. Wirewound ferrite chokes provide more design flexibility with a high magnitude of attenuation over a wide frequency range, lower dc resistance, and higher current ratings. While chip ferrite beads offer value, the devices have a limited attenuation and frequency range.

When we place two halves of ferrite around a conducting wire--such as a power cable, we have a ferrite clamp that provides an inductive impedance for signals traveling through the cable. Ferrite clamps and chokes follow Faraday’s Law in that a magnetic core place around a conductor induces a back electromagnetic force (EMF) in the presence of a high frequency signal. Given the high permeability of ferrite, the material offers less resistance than to the flow of magnetic flux in the conductor and--as a result--the ferrite absorbs noise.

Match the Best Ferrite Choke or Clamp to the Application

Selecting a ferrite choke or clamp depends on the source of the EMI and the range of unwanted frequencies because the undesired frequencies must match with a resistive band of the choke or clamp. Along with matching the choke or clamp to frequency requirements, the rated dc current of the device must match with the currents seen in the circuit. If the circuit current increases beyond the rated current, saturation occurs and the choke or clamp will become 50% less inductive and have impedance reduced by 90%. With those changes, the choke or clamp cannot suppress EMI.

Because ferrite chokes and clamps are resistive, the devices can cause voltage drops in a circuit. The resistive properties of ferrite devices also may cause unwanted heating as high frequency energy dissipates. Always check the manufacturer’s specifications for the maximum DC current, and the DC resistance rating. Any ferrite choke or clamp must have a DC current rating more than twice the value of the required current for the rail. Design teams can use PCB design software and design rules to determine the correct placement for chokes to avoid voltage drop issues.

Ferrite materials over small components

Ferrite materials covering components can help avoid interference related issues.


The manufacturer’s specifications for ferrite chokes or clamps include impedance versus load current curves that show the characteristics of the devices at specific currents. The manufacturer’s specifications for ferrite chokes and clamps also show impedance versus frequency response. In addition, most manufacturers include equivalent circuit models for ferrite chokes and clamps that work for system simulations.

Because ferrite chokes are inductive and capacitive, circuit designs must also account for “Q” or the reactance of the inductor divided by the ac or rf resistance plus any dc resistance found in the choke windings. Chokes that have a high Q can create unwanted resonance in power isolation circuits. PCB design software provides the analytic tools to find the approximate value of ferrite choke inductance and to determine the resonant frequency cutoff.

The suite of design and analysis tools available from Cadence is here to help minimize the difficulty of your manufacturing process. Utilizing OrCAD PCB Designer is a great way to give your designers the layout capacity they need to finalize designs in a seamless manner. 

If you’re looking to learn more about how Cadence has the solution for you, talk to us and our team of experts

About the Author

Cadence PCB solutions is a complete front to back design tool to enable fast and efficient product creation. Cadence enables users accurately shorten design cycles to hand off to manufacturing through modern, IPC-2581 industry standard.

Follow on Linkedin Visit Website More Content by Cadence PCB Solutions
Previous Article
Choosing Types of Pins For Your PCB Design
Choosing Types of Pins For Your PCB Design

The types of pins used in your circuits impacts everything like signals, temperature, voltage, and current.

Next Article
Configuring For DC Power Supply Limitations
Configuring For DC Power Supply Limitations

DC power supply limitations include proper traces, ground plane management, and component selection.